How to put a trampoline together? Easy assembly steps

William Adams
 min read

How to put a trampoline together? It’s not as difficult as you think.

How to put a trampoline together? Easy assembly stepsBefore using a new trampoline, it is essential to assemble it by following each assembly step scrupulously.

As a general rule, every trampoline will be accompanied by a manual that shows how to assemble it. Make sure to check all the components, prepare the ground for installation, assemble the frame, then the legs, the mat and the cushion, ending with the posts and safety net, if applicable.

All components must be installed appropriately for the structure to be safe to use.

Even though a trampoline comes with an installation manual on how to put it together, understanding the setup can be complicated, so read on to make sure you’ve got it right and ease your mind.

How to put a trampoline together? Introduction

How to put a trampoline together includes:

  • Finding a suitable floor
  • Assembling the tubes
  • Stretching the jumping surface with the springs
  • Placing the posts and net

Through this guide, we show you how to assemble a trampoline, make sure you have the necessary tools, and you’ll be on your way!

Unpack and check the contents

Of course, before starting the trampoline assembly, it is important to check the whole set. Unpack your package and refer to the instructions for your trampoline.

At first glance, you should immediately see if the trampoline that has just arrived matches the images of the model you have selected. If so, you’re already good to go.

Each trampoline may have different accessories than the others. Thus, one model may well have elements that others do not.

Here are the main components that must be included in the package:

  • screws and nuts
  • springs
  • safety cushion
  • safety net (optional)
  • tubes (to form the frame)
  • jumping canvas
  • ladder, the protective cover, and the anchoring kit are among the options for a trampoline. Depending on the model chosen, they may or may not be included in the set.
  • posts (the legs of the trampoline)

Now inspect all of these parts to see if they conform to your order.

If there are no deficiencies, you can proceed with the actual installation.

Prepare the ground for the trampoline

This step is critical as it will determine the stability of the trampoline. Trampolines that are well set up are always the ones that are safe to use.

As a general rule, a trampoline should be placed on a flat, reasonably hard, non-slippery floor. When it comes to flat ground, choose a space with no slope.

Indeed, the inclination of the ground can destabilize the structure and risk causing an accident.

As far as the floor is concerned, it is recommended to choose a compact area to avoid burying the feet of the trampoline.

For the buried trampoline versions, it will be necessary to dig according to the model’s recommendations.

Related post: Can you put a trampoline in the ground?

In any case, the location of a trampoline should be in a clear space. This will not only make assembly more manageable but will also ensure the safety of the users.

Therefore, avoid mounting a trampoline too close to the set. Choose a location in the garden away from trees, bushes, fences, and pools.

How to set up a trampoline?

Installing a backyard trampoline can be complicated for some, but following the proper instructions will have you doing it in no time.

Trampoline frame assembly

It all starts with the assembly of the trampoline frame.

Usually, the tubes that form the frame are combined with T-joints. Typically, screws are provided to consolidate the whole.

Depending on the model, bolts can be used to replace the simple screw. Depending on this, you will need a screwdriver or a wrench.

You will now fit the tubes and fittings together, ensuring that the joint is tight. Once you have completed this step, you will have a circular tube.

Assemble the legs on the circle

The legs of a trampoline can be vertical metal bars or a U-shaped tube.

They can be composed of several pieces, just like the circular frame.

Like the tubes, the feet will fit into the bottom of the T-fitting.

Simply insert them in the right place and screw them in place. Remember to tighten these components securely.

Installing the jumping sheet

This step is the most delicate since it will be necessary to ensure the installation of all the springs. On the trampoline frame, there are holes located at regular intervals.

These will be used to receive the springs. The springs hold and tension the jumping surface and ensure that all these elements are correctly installed.

First, attach each spring to the circular tube and once you have gone around, hang the canvas on the springs.

You will, of course, do this one by one while moving to the opposite side after each assembly.

Installing the protective cushion

At this point, you are in the final stages of trampoline installation. The protective pad will cover the springs from above.

The protective cushion is an element that will secure users by preventing their feet from slipping between the springs.

Generally, it attaches below the springs and is very easy to install since it unfolds over the entire diameter of the canvas.

Place the safety net and the posts

The safety net protects users from falling out of the structure.

As for the uprights, they will be used to hold and tighten the net.

They exist in two forms:

  • One for the lower part and
  • One for the top

To begin, insert the mounting screws into the bottom post. These screws will go right into one of the legs of the trampoline.

The safety net is equipped with sleeves for the upper part to go over the upright supports.

You have to connect the top and bottom posts after installing the bottom tubes and the net.

Installing the trampoline’s additional accessories

Other pieces can complete the set depending on the trampoline version.

These include the ladder, shoe net, lower safety net, protective cover, and anchor kit.

The ladder is often included in the trampoline package, but sometimes it will be necessary to purchase it separately. It will be placed facing the entrance on the net.

When the trampoline is not in use, remember to remove the ladder to prevent unsupervised access by children.

As the name suggests, the shoe net will be used to collect the users’ shoes. It is easily placed on the trampoline frame. This accessory will gather the shoes to avoid scattering them everywhere.

The safety net for the lower part prevents children from sliding under the structure. Attach this accessory to the frame to secure this area under the trampoline.

The anchoring kit accessory will improve the stability of the trampoline. To properly anchor the trampoline, there is often no need to dig.

Instead, some kits allow you to simply screw the anchors into the ground and connect it to the bottom tubes.

Finally, the protective cover should be installed when the trampoline is not used.

It will protect the equipment against bad weather, dust, and possible dead leaves.

How to put a trampoline together? Conclusion

Although every new trampoline should have a detailed manual with all the steps needed, this article will help you consider the holistic setup including the surrounding areas.

Take your time to do it properly, and you’re guaranteed many hours of safe, fat-burning fun!

Related postIs trampolining good for obese people? Rebounding for weight loss

About William Adams

I’m an engineer and a happy plus-size individual myself. I love to blog online if I can have a positive impact on the lives of others. I help other plus-size people with in-depth product guides to make shopping for products and services less stressful in their busy lives. Read More